2.2.4. Adjustment of seats and head restraints

The design of seats of the car guarantees the maximum comfort to the person sitting in them, at the same time providing conditions of the most effective implementation of the functions with belts and safety cushions. The choice of provision of a seat also exerts impact on safety of the person sitting in it. For example, at the excessive shift of a front seat the risk of the traumatizing sitting at operation of a safety cushion, and also risk of ejection through a windshield at head-on collision increases forward.

Increase in an inclination of a seatback will worsen fixing of a body a seat belt, - the more the back is rejected back, the probability of slipping of a body of the belt sitting under zone section at strong front blow is higher, and the heavier can be traumatized.

Adjustment of height of a head restraint


  1. Record a front seat in the most remote (convenient for driving) from a steering wheel / dashboard situation, bring a back into vertical position.
  2. Head restraints prevent traumatizing cervical department of a backbone and head at blow behind. The head restraint should be adjusted on height so that its top cut was flush with the upper edge of the ear sitting.
  3. For lowering of head restraints of front seats, and also back seats of the Station wagon models, press a clamp and press a head restraint into a seat.
  1. Head restraints of back seats of the Sedan models have two provisions – vertical and horizontal. For moving of a head restraint to horizontal position (for increase in the review through back glass) press a clamp.

Adjustment of front seats is made manually, Ljubo by means of the electric drive (depending on a complete set). Manually it is possible to regulate the seat height, its situation in the longitudinal direction, a seat inclination completely and separately its backs, rigidity of a lumbar support and height of a head restraint. By means of э / the drive it is possible to regulate the seat height, its situation in the longitudinal direction and a back inclination.

Manual adjustment of provision of front seats


  1. For lifting/lowering of a seat pull the regulator respectively up down. After an otpuskaniye the regulator comes back to a starting position.

  1. For adjustment of horizontal position of a seat lift the bracket located under a forward part of a pillow, and move a seat to required position then make sure of reliability of fixing of a seat.
  1. Adjustment of an inclination of a chair is carried out at the delayed lever located at edge of a seat.
  1. Adjustment of an inclination of a seatback and the provision of a lumbar support is carried out by rotation of the corresponding adjusting wheels. After adjustment of an inclination of a back make sure of reliability of its fixing.

Adjustment of front seats with э / the drive and function of memory

Э / the drive of seats and function of memory of provisions of a seat of the driver and external rear-view mirrors are installed as the additional equipment.

If doors are closed, э / the drive of seats it is necessary for functioning that the ignition key was in the provision of "ON". However э / the drive works during 30 from later closing of both doors. If the provision of a seat changes during these 30 with, then new counting of 30 pages begins.


  1. For seat height adjustment lift or press the lower regulator located sideways on a seat pillow. It is possible to establish by the same regulator height of forward and back parts of a pillow of a seat independently from each other.
  2. Movement of a seat in the longitudinal direction is carried out when moving the lower regulator forward or back.
  3. For adjustment of an inclination of a back of a chair move forward or back the top regulator.

Function of memory of provisions of a seat of the driver remembers also control of rear-view mirrors. For entering in memory of the current provision of a seat and mirrors, holding pressed the M button, press one of buttons of memory (1, 2 or 3).

Location of the control panel of setting up provision of a seat

In confirmation of entering in memory the sound signal is distributed. For installation of sitting and rear-view mirrors in the remembered situation, hold the memory pressed the corresponding button.

Folding of back seats

For increase in volume of the luggage compartment the possibility of folding of a back seat is provided.

Narrow and wide parts of a seat can be put separately.

Folding of a back seat of the Sedan model


  1. Cast away seat pillows forward, having pulled for the loops (1) located in their back parts.
  2. Put pillows of seats on high edge behind front seats (2). Having pressed the side buttons (3), release backs from clamps and lower forward.
  3. At return of a back seat to a starting position suspend seat belts on hooks for clothes (on the top handles) that belts were not jammed by a back.
  4. After assembly of a seat make sure that buttons of removal of fixing of backs are aflush with their frame.