bcee4405

13.1. External equipment and body elements

Removal and installation of bumpers

Front bumper of models till 2002 of the issue.

 PERFORMANCE ORDER

  1. Remove a decorative front grille (see the Section Removal and installation of decorative front grilles), indexes of turns and levers of cleaners of headlights (see the Head Onboard electric equipment).
  1. Turn out 4 bolts (4) fastenings of a bumper to a beam (2 behind indexes of turns and 2 on a bumper beam) and give nuts (5) of fastening of a bumper to wings
  1. Turn out bolts of fastening of loker to a bumper.
  1. Remove the lower protection cover of a motive compartment, separate sockets of fog lights (see the Head Onboard electric equipment) and temperature sensor.
  1. Unhook external corners on both sides of a bumper from wings and loker and remove a bumper, having pulled it forward.
  1. At installation of a new bumper transfer to it from an old bumper a spoiler and a plate of registration plate.
  1. Make sure that metal holders (9 pieces) are not lost and are not bent.
  1. Establish a bumper on a beam, watching that limiters of levers of cleaners of headlights and their shaft э / motors correctly settled down concerning a bumper.
  2. Further installation is made as it should be, the return to an order of dismantle of components. In conclusion check serviceability of functioning of indexes of turns, fog lights and cleaners of headlights.

Front bumper of models since 2002 of the issue.

 PERFORMANCE ORDER

  1. Remove side decorative front grilles (see the Section Removal and installation of decorative front grilles) and a cover of the rechargeable battery.
  2. Remove indexes of turns and a headlight (see the Head Onboard electric equipment).
  1. Turn out bolts of fastening of a bumper to a beam.
  1. Remove a protective cover of washers of headlights, having squeezed its clamps and turn out bolts of fastening of loker to a bumper.
  1. Remove the lower protection cover of a motive compartment and the top clamps of a bumper.
  1. Unhook external corners on both sides of a bumper from wings and loker and separate sockets of fog lights and the sensor of temperature.
  2. Delay a bumper on each side and remove it from six clamps.
  1. In need of removal of an arm of a bumper slightly turn out bolts of fastening of washers of headlights, turn out 4 bolts of fastening of an arm (3) and weaken a collar (4).
  1. At installation of a new bumper transfer to it from an old bumper a spoiler, a plate of registration plate, moldings and the lower decorative front grille.
  2. Installation is made upside-down.

Rear bumper of the Sedan models

 PERFORMANCE ORDER

  1. Turn out two screws (1) from each wheel arch.
  1. Open a trunk lid and remove the lower overlay of an aperture of the luggage compartment.
  1. Unbend a carpet of the luggage compartment (4). On models since 2002 of the issue remove consolidations then give nuts of fastening of a bumper (5).
  1. On models till 2002 of the issue remove an angular pro-rate under the back combined lamp (5).
  1. On models since 2002 of the issue remove moldings (6) and give nuts (7) from two openings behind a back molding.
  1. At a complete set the coupling device separate its sockets and turn out bolts of its fastening to a body.
  1. Together with the assistant remove a bumper from clamps and pull it back. At the corresponding complete set separate the socket of the sensor of system of the help at the parking (1).
  1. In need of removal of arms of fastening of a rear bumper of models since 2002 turn out the issue bolts of fastening of an arm.
  1. Installation is made upside-down.

Rear bumper and top shelf of a bumper of the Station wagon models

 PERFORMANCE ORDER

  1. Open a back door. On models since 2002 of the issue remove angular moldings of a rear bumper.
  1. Turn out screws of fastening of the top shelf of a bumper (3).
  1. Liberate bottom edge of the shelf of a bumper from clamps, slightly unbend its corner and remove it, having pulled directly back. At the corresponding complete set separate sockets of sensors of the help at the parking.
  2. Turn out two screws from each wheel arch.
  1. Remove ware boxes (4) and the isolating plates (5) in the luggage compartment. On models till 2002 of the issue remove the back combined lamps (see the Head Onboard electric equipment).
  1. Give bumper fixture.
  1. At a complete set the coupling device separate its sockets and turn out bolts of its fastening to a body.
  2. Together with the assistant remove a bumper from clamps and pull it back. At the corresponding complete set separate sockets of sensors of system of the help at the parking.
  3. Installation is made upside-down.